30
Siren Secondary Entrapment / Indicating Light For Gate Position
Light illuminates anytime gate is not closed (4 second delay)
Security Shunt Circuit
(N/O relay contact)
This option allows the gate to be activated by a control device without activating the home alarm. The home
alarm will activate if gate is forced opened. Security shunt relay will release 4 seconds after close limit. Wire
in parallel with gate switch, which is wired into home alarm system.
Magnetic Lock Wiring / Stone Lock or any 12 volt DC Solenoid Lock/Siren
+12vdc
siren
+12 volt
ground
Secondary
Entrapment
Siren Wirin
ADJUSTMENT
5
Siren Output
S1
LED INDICATOR
S2
RESET
OPEN/CLOSE
COMMAND
Entrapment
Vehicular Gate Operator
Gate Weight Max. Load: 650 lbs.
S
E
C
U
R
I
T
Y
S
H
U
N
T
C
O
M
M
O
N
G
N
D
M
A
G
L
O
C
K
S
O
L
O
N
O
I
D
L
O
C
K
C
O
M
M
O
N
G
N
D
O
U
T
P
U
T
+
1
2
V
O
N
SOLONOID LOCK ENABLE
MAGNETIC LOCK ENABLE
SECURITY SHUNT ENABLE
MOTION DETECTOR ENABLE
15
15
CURRENT SENSE
0
10
5
ADJUSTMENT
Sensitivity
0
10
TIME R TO CLOSE
Tim er
Class I or Class II per UL325
J2 INDICATORS
1- +12V OUT 1.5 AMP MAX
2- COMMON GROUND
3- PUSH BUTTON INPUT
4- OPEN SAFETY EDGE
5- CLOSE INPUT
6- SECONDARY ENTRAPMENT DEVICE INPUT
7- COMMON GROUND
8- STOP CI RCUIT INP UT N/C
9- FREE EXIT / OPEN INPUT
10- UNDER GATE / CENTER LOOP INPUT
11- SAFETY LOOP / REVERSING EDGE INPUT
12- MOTION DETECTOR INPUT
1 2 3 4 5 6 7 8 9 10 11 12
J2
BOTH ON FOR DUAL
DS1 SWITCH SETTINGS FACTORY SETTINGS
SW-1 AUTO CLOSE TIMER DISABLE OFF
SW-2 TIMER TO CLOSE WILL ACTIVATE ON LIMIT ONLY ON
SW-3 MASTER GATE ENABLE ON
SW-4 SLAVE GATE ENABLE OFF
SW-5 NOT USED OFF
SW-6 SOFT START/STOP RETRACT ENABLE OFF
SW-7 SOFT START/STOP EXTEND ENABLE OFF
SW-8 STOP CIRCUIT ENABLE OFF
SW-9 OPERATING DIRECTION REVERSE OFF
SW-10 CUSTOM SOFTWARE ENABLE OFF
1
2
3
4
5
6
7
8
9
10
O
N
DS1
PATRIOT CONTROL BOARD
USAutomatic
MADE IN USA
1 2 3 4 5 6 7 8 9 10 11 12
S S
e h
c u
u n
r t
i
t
S S
e h
c u
u n
r t
i
t
Program function switch DS2
switch #3 must be “ON” for
circuit to operate.
Leading edge of gate and fence
post shown using closed type
roximit
switch.
ADJUSTMENT
5
Siren Output
S1
LED INDICATOR
S2
RESET
OPEN/CLOSE
COMMAND
Entrapment
Vehicular Gate Operator
Gate Weight Max. Load: 650
S
E
C
U
R
I
T
S
H
U
N
C
O
M
M
O
N
G
N
D
M
A
G
L
O
C
S
O
L
O
N
O
I
D
L
O
C
C
O
M
M
O
N
G
N
O
U
T
P
U
T
+
1
2
O
SOLONOID LOCK ENABLE
MAGNETIC LOCK ENABLE
SECURITY SHUNT ENABLE
15
15
CURRENT SENSE
0
10
5
ADJUSTMENT
Sensitivit
0
10
TIME R TO CLOSE
Tim er
Class I or Class II per
J2 INDICATORS
1- +12V OUT 1.5 AMP MAX
2- COMMON GROUND
3- PUSH BUTTON INPUT
4- OPEN SAFETY EDGE
5- CLOSE INPUT
6- SECONDARY ENTRAPMENT DEVICE INPUT
7- COMMON GROUND
8- STOP CI RCUIT INP UT N/C
9- FREE EXIT / OPEN INPUT
10- UNDER GATE / CENTER LOOP INPUT
11- SAFETY LOOP / REVERSING EDGE INPUT
J2
BOTH ON FOR DUAL
DS1 SWITCH SETTINGS FACTORY
SETTINGS
SW-1 AUTO CLOSE TIMER DISABLE OFF
SW-2 TIMER TO CLOSE WILL ACTIVATE ON LIMIT ONLY ON
SW-3 MASTER GATE ENABLE ON
SW-4 SLAVE GATE ENABLE OFF
SW-5 NOT USED OFF
SW-6 SOFT START/STOP RETRACT ENABLE OFF
SW-7 SOFT START/STOP EXTEND ENABLE OFF
SW-8 STOP CIRCUIT ENABLE OFF
SW-9 OPERATING DIRECTION REVERSE OFF
1
2
3
4
5
6
7
8
9
O
N
DS1
PATRIOT CONTROL BOARD
USAutomatic
MADE IN USA
The Mag lock outputs +12vdc when the gate is on the closed
limit. When the control board receives an open input the mag
lock output goes to 0vdc .5 seconds before the gate begins to
move.
The Solenoid / Siren output is +12vdc 1 second before the
gate begins to open or close from a limit. The +12vdc output
will remain until a limit is reached plus a 4 second delay. The
control board will output the +12vdc 1 second before the gate
begins to move and will output +12vdc for 4 seconds after the
gate limit is reached. This also allows a siren or light to be
operated prior to movement.
The output is regulated to 1.5 amps by a autoreset able fuse.
Mag lock and Solenoid lock outputs are labeled
On the circuit board. Take care when running
wires to avoid pinch areas.
OTE: The corresponding DS2 switch must be
turned on for the desired output to function.
Both outputs can be used as long as the current
draw does not exceed 1.5 amps.