SAFES
OWNER'S MANUAL
□ TS20-30
口TS26-45
OD: 57"H x 28"W x 20" D
ID: 53.8" H x 25.7" W x 14.7" D
Weight: 363 lbs.
Gun Capacity: 26
Fire: 45 min @ 1400 degrees
TSC SKU: 1360473
***
Attention! Please Read
First!
***
口
T
S36-45
OD: 5
9
"H x 3
0
"W x 22" D
ID: 56.6" H x 28.2" W x 16.3" D
Weight: 405 lbs.
Gun Capacity: 36
Fire: 45 min @ 1400 degrees
TSC SKU: 1552547
OD: 56"H x 22"W x 20" D
ID: 53.6" H x 1
9
" W x 14.8" D
Weight: 328 lbs.
Gun Capacity: 20
Fire: 30 min @ 1400 degrees
TSC SKU: 1
9
65574
www.winchestersafes.com
Owner’s Manual
NOTES:
For Support, visit www.winchestersafes.com
Customer Service
HOURS: 7:30am - 3:30pm CST!
Monday thru Friday!
Email: [email protected]
www.winchestersafes.com
Owner’s Manual
DELIVERY AND INSTALLATION
A. If you purchased your safe from a retailer and are having it delivered and installed, the
delivery company personnel will provide you with the proper instruction for the correct
operation of your safe. Pay very close attention to the operation of the lock. Make sure you
can comfortably operate the lock before they leave your home or office. After they have
shown you how to operate the lock, you should lock and unlock the safe several times
without any assistance from them. Once you are comfortable with this procedure, and can do
it consistently, you are now ready to operate your safe.
Your new safe left the factory in new condition and without damage. Inspect your new safe
for any damage prior to the delivery personnel leaving. Any damage claims at time of
delivery must be resolved with the delivery company and/or your retailer. Please do not
contact the factory.
B. If you purchased your safe and are doing your own delivery and installation, you must
read and follow these instructions. Safes are heavy and cumbersome and
there are risks associated with the untrained consumer doing their own delivery and
installation. We recommend that you use a professional safe installer, who is insured, and
will have the necessary equipment and training to safely and properly install your safe.
1. Packaging should have been removed and safe inspected for damage prior to accepting the
safe from your retailer. If your safe is damaged at this point, please contact your retailer. Do
not contact the factory.
2 .Verify that the Serial Numbers on the safe are the same as the one in this manual. Serial
Numbers are located on the bottom right side of the safe’s front and also on the upper part of
the inside door, near the locking bolts. In the unlikely event that all three serial numbers do
not match exactly, please contact theWinchester Safes Customer Service Department.
www.winchestersafes.com
Owner’s Manual
DELIVERY AND INSTALLATION (CONTINUED)
3. Your safe was shipped with the door closed and locked . Open the safe by following the
INSTALLING THE BATTERY ON A ELECTRONIC LOCK instructions and the
ELECTRONIC LOCK OPERATING INSTRUCTIONS.
4. Remove the safe from the pallet by first opening safe the door. Find and remove the (4)
four decorative plugs in the safe bottom. Using a 17mm socket and ratchet, remove the four
lag bolts that secure the safe to the pallet. Reinstall the four decorative plugs. Next, close the
safe door and extend the locking bolts by rotating the handle counterclockwise. With the
assistance of one or more adults, slide the safe to one side of the pallet to prevent it from
tipping over. Tilt the safe over until the bottom side of the safe touches the floor, and then tilt
the safe over enough to allow the pallet to be removed from under the safe. Tilt the safe
backup and set flat on the floor.
5. With a dolly substantial enough to support the size and weight of your safe, move the safe
to your desired location. Consideration should be given to the weight of the safe and the type
of flooring that the safe will be moved across. Wood, tile, carpet and other types of flooring
can be easily damaged and it is your responsibility to take whatever measures necessary to
prevent any damage. If your home is pier and beam construction, you should place the safe
in an area of the floor that you are sure will support the safe’s weight.
To maximize the fire protection of your safe, we recommend you place it in the lowest
elevation in your home. In a home fire, the coolest part of the fire is in the basement area and
the hottest in the upstairs.
6. To maximize the burglary protection, and prevent the safe from tipping over, you MUST
anchor your safe to the floor.
7. Your new Winchester Safe is now ready to operate.
www.winchestersafes.com
Owner’s Manual
Installing the Battery
Step 1 - Remove the Key Pad Housing - while depressing the small button located on
the bottom on the key pad housing, rotate the keypad counter- clockwise (left) and
remove the key pad housing to access the battery connection. REF IMAGE 1.1
Step 2 - Connect the 9V Alkaline battery, gently insert the battery inside the key pad
housing. REF IMAFE 1.2
Step 3 - Put the cover back on the keypad base.
Step 4 - Rotate the cover clockwise (right) 30° until it is back to the original upright
position.
IMAGE 1.1 IMAGE 1.2
www.winchestersafes.com
Owner’s Manual
Operating the Safe
For TS26-45 or TS36-45, please refer to the next page
for temporary spoke and handles installation firstly.
www.winchestersafes.com
Owner’s Manual
Step 1 - Locate the temporary spoke.
WARNING: Do not apply Spoke Handle
Thread Lock on temporary spoke.
Step 2 - Screw in the temporary spoke
at the bottom of the handle hub.
(Return to these steps after completing instructions on next page.)
INSTALLING THE HANDLE SPOKES
Step 1 - Remove and discard the temporary
spoke.
Step 2 - Remove the box of spokes from
inside of the safe. Unpack each spoke and
apply one drop of Spoke Handle Thread Lock
on the threads before screwing in the handles.
Step 3 - Screw handles into the spoke hub.
Images are for instruction only and may not look identical to the handle on the
safe you have purchased.
INSTALLING THE TEMPORARY SPOKE (Actual number of spokes may vary.)
The temporary spoke provided is used to assist in opening the safe for the first time
ONLY!
www.winchestersafes.com
Owner’s Manual
Backup Key Operation
Step 1 - Remove the Key Pad Housing - while depressing the small button located on
the bottom on the key pad housing, rotate the keypad counter- clockwise (left) and
remove the key pad housing.
REF IMAGE 1.3
Step 2 - Using the provided keys (ref: image 1.4), insert the key and rotate clockwise
until it stops.
Step 3 - While holding the key, turn the safe door handle, clockwise to open the door.
IMAGE 1.3
IMAGE 1.5
IMAGE 1.4
6
www.winchestersafes.com
Owner’s Manual
7
www.winchestersafes.com
Owner’s Manual
8
www.winchestersafes.com
Owner’s Manual
LIMITED LIFETIME WARRANTY
This safe made by Granite Security Products, Inc . (GSP) comes with a limited lifetime
warranty, beginning on the purchase date against defects in materials and workmanship. . Proof
of purchase is required to obtain service.
Lock: 1-year from the purchase date. One override key is provided with each safe. Replacement keys
are shipped at $50 each, plus S&H.
Locking System: 5-years from purchase date. Includes the handle and spokes, bolt work mechanism
and locking bolts.
This warranty does not cover neglect, misuse, or abuse . It also does not cover damage caused
by tampering with or altering of any part of the product. It also does not cover consumables
such as batteries for the electronic lock. The safe must not be housed in an enclosed swimming
pool area. The safe is to be located in an area which is climate controlled and is to be installed as
instructed in the Owner’s Manual.
The Limited Lifetime Warranty is non-transferred.
Certain exclusions to this warranty are: safes used in a commercial or industrial environment,
water damage of any kind, paint finish, and loss or damage of personal property inside the safe.
This warranty also does not apply to safes located outside the contiguous United States.
GSP provides this warranty in place of all other warranties and assurances whether expressed or
implied. GSP accepts no liability for incidental or consequential damage or loss by anyone as a
result of using this safe .
To activate this warranty, please go online to complete the registration at
www.winchestersafes.com
9
19-TSC-00
